search

Moxa CP-138U-I-T Bedienungsanleitung Seite 28

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 141
  • Inhaltsverzeichnis
  • LESEZEICHEN
    • Bewertet. / 5. Basierend auf Kundenbewertungen
Seitenansicht 27
Universal PCI Board User’s Manual Hardware Installation
2-15
The onboard DIP switches are used to configure the CP-102UF for “Ring mode” or “Normal”.
When using the CP-102UF board, your PC can be included as one node of a fiber ring formed using
Moxa’s own TCF-142 serial-to-fiber converter. Since each TCF-142 has two fiber ports and one
serial port, PCs that are part of the ring will be able to communicate with serial devices connected to
the ring. Note that the Tx port of the CP-102UF connects to a neighboring converter’s Rx port to
form the ring. When one node transmits a signal, the signal travels around the ring until it returns
back to the transmitting unit, which then blocks the signals.
Port 1
Port 2
PC
CP-102UF
TCF-142
RS-232RS-422
RS-485
5210
TCF-142-S
Serial to Fiber Converter
RS-232/422/485
+T
T-
+D
/
+R
-D
/
-
R
xT
xR
D
NG
RS-422/485 RS-232
12-48V
+V
V
-
5210
TCF-142-S
Serial to Fiber Converter
RS-232/422/485
+
T
T
-
+
D
/
+R
-D
/-
R
xT
xR
D
NG
RS-422/485 RS-232
12-48V
+V
V
-
5210
TCF-142-S
Serial to Fiber Converter
RS-232/422/485
+T
T
-
+D/+
R
-D
/-
R
xT
xR
DNG
RS-422/485 RS-232
12-48V
+V
V-
TCF-142
RS-232RS-422
RS-485
5210
TCF-142-S
Serial to Fiber Converter
RS-232/422/485
+T
T
-
+
D
/
+
R
-D
/
-R
xT
xR
D
NG
RS-422/485 RS-232
12-48V
+V
V
-
5210
TCF-142-S
Serial to Fiber Converter
RS-232/422/485
+T
T
-
+
D
/
+
R
-
D
/
-
R
xT
x
R
DNG
RS-422/485 RS-232
12-48V
+V
V
-
5210
TCF-142-S
Serial to Fiber Converter
RS-232/422/485
+T
T
-
+
D
/
+
R
-
D
/
-
R
x
T
x
R
DNG
RS-422/485 RS-232
12-48V
+V
V
-
NOTE: When configuring two or more CP-102UF boards installed in the same computer, please
pay attention to the model names of the boards. The two models can be recognized by the type of
connector on the board. Model CP-102UF-M uses plastic ST connectors, whereas model
CP-102UF-S uses metal ST connectors.
Plugging the Board into an Expansion Slot
ATTENTION
Safety First!
To avoid damaging your system and board, make sure your PC’s power is turned off before
installing your Universal PCI Board.
Step 1:
Power off the PC.
Step 2:
Shut off the power to any peripheral devices and remove the PC’s cover.
Step 3:
Configure the UPCI board’s DIP switches and jumpers as necessary. This only applies to
certain models. For additional information, please refer to your model in this chapter.
Step 4:
Insert the board firmly into a free PCI or PCI-X slot on the PC.
Step 6:
Use a screw to secure the board in place.
Step 7:
Replace the PC’s cover.
Step 8:
Power on the PC. The BIOS will automatically set the IRQ and I/O address.
Step 9:
Install the software. For details, please refer to the appropriate chapter for your operating
system.
Seitenansicht 27
1 2 ... 23 24 25 26 27 28 29 30 31 32 33 ... 140 141

Kommentare zu diesen Handbüchern

Keine Kommentare
  • Lenmar Enterprises Dynojet Research Certikin Gastroback Alex
  • Aluratek Kartenleser Atlas Sound Zusätzliche Musikausrüstung Insignia Auto-Audio-Verstärker Crown Boiler Warmwasserbereiter & Kessel Canon Öffentliche Anzeigen
  • Safco 4132GR Samsung SGH-M300 Philips AJ3226/12 AEG F99705VI1P Kodak M873
  • Miele HS12 Bedienungsanleitung VTech LS6245 Bedienungsanleitung Whirlpool SMP 658C/BT/IXL Bedienungsanleitung Metrologic MS7120 Orbit Betriebsanweisung Dell Latitude D620 Bedienungsanleitung